Cutters Edge Guard Depth Gauge Series Spezifikationen Seite 1

CUTTERS EDGEVentilation SawsCE-670-FDV SERIES ANDGUARD/DEPTH GAUGE SERIESCE-670-FDV/D6CE-670-FDV/D8

10 / CUTTERS EDGE VENTILATION SAWSPull the chain around the bar to be sure the drive links areproperly seated in the drive sprocket.Now replace the ou

Next remove the bar and chain oil tank cap and fill the tankwith bar and chain oil. Replace the cap.You do not need special detergent oils, as the cha

12 / CUTTERS EDGE VENTILATION SAWSNOTENote that you must depress the safety lock on topof the handle to he able to pull the trigger (Fig. 14).The trig

Cutters Edge D-8 & D-6 Guard/Depth GaugeInstallation, Operation & Maintenance*Cutters Edge D-8 & D-6 Guard/Depth GaugeThe Cutters Edge D-8

14/CUTTERS EDGE VENTILATION SAWSNOTEIf you are upgrading your saw with a D-S Kit:Before proceeding you will first need to removethe chain tension adju

Position the outer section properly, with the spacers be-tween the cutters on the chain. Tap it into place.The Adjusting KnobsTo install the adjusting

16 / CUTTERS EDGE VENTILATION SAWSCutting deeper than the D-8 settingEven with the D-8 set to a pre-determined depth you canincrease the depth of your

PartTwoOperationWithout Guard/Depth Gauge InstalledAfter proper set-up and running-in, your Cutters EdgeVentilation Saw will be available for service.

18 / CUTTERS EDGE VENTILATION SAWSONE-STEP STARTING PROCEDURESince you have properly warmed up the saw, you can startit now using the One-Step Startin

OPERATION & MAINTENANCE / 19Fig. 19. Pull up and over the rafter ...VENTILATION CUTSThere are many types of ventilation cuts. We will demon-strate

Copyright © 1992 Edge Industries, Inc.All rights reserved. No part of this manual may be reproduced or transmitted in any form orbyany means, electron

20 / CUTTERS EDGE VENTILATION SAWSLOUVERSTRIPTo louver, start with a head cut parallel to the rafterdirection, rolling any rafters. The rafters will b

Part ThreeMaintenance21After use, your Cutters Edge Ventilation Saw should becleaned and inspected. Werecommend that you develop adepartmental standar

22 / CUTTERS EDGE VENTILATION SAWSNOTEWe recommend lubricating your sprocket tip assoon as safely possible after cutting, while the baris still hot. I

OPERATION & MAINTENANCE / 23CYLINDER HEADREASSEMBLYNow remove the carburetor compartment cover by firstloosening the two screws (Fig. 30).Then rem

24/CUTTERS EDGE VENTILATION SAWSENGINETYPE: Single-cylinder 2-cycle, with loop scavengingDISPLACEMENT: 4.1 cu. in. (66.8cc)BORE: 1.97 in. (50mm)STROKE

PARTS & ACCESSORIESCUTTERS EDGE FIRE DEPARTMENT CARBIDE TIPPED CHAIN12" chain loop16" chain loop20" chain loop#B3E-400SX47#B3E-400S

As Limited Below,Edge Industries, Inc., warrant to the original retail purchaser that this Cutters Edge Saw is free from defects in materials and work

ORDER FORM VENTILATION METHODS AND TECHNIQUES by John Mittendorf Please send me ( ) copy (copies) of Ventilation Methods and Techniques. Name:______

Cutters Edge OfficesP.O. Box 8463855 23rd StreetBaker City, Oregon 97814Telephone: 541-524-9999Fax: 541-524-9996Email [email protected] Coast S

Cutters Edge Ventilation Saws Operation & Maintenance CUTTERS EDGE P.O. Box 846 3855 23rd Street Baker City, Oregon 97814

Cutters Edge Ventilation SawsOperation & MaintenanceTable of ContentsINTRODUCTIONKICKBACK WARNINGDESCRIPTIONPart OneSET-UPD6 & D8 GUARD / DEPT

CUTTERS EDGE VENTILATION SAWSOPERATION & TRAINING MANUALEdge Industries, Inc.OPERATION & MAINTENANCE / 5The purpose of ventilation is the esta

6 / OPERATION & MAINTENANCEWARNINGBeware of kickback!There are two types of kickback that can be encountered with the improper use of a chainsaw o

OPERATION & MAINTENANCE/7YOUR CUTTERS EDGE VENTILATION SAWWhen you receive your Cutters Edge Ventilation Saw, check that all of the following are

Part OneSet-UpThis section will cover assembly of the saw and prepara-tion for operation. All necessary tools and equipment havebeen included with you

THE BAR PLATESNow remove the outer bar plate. Note that the two barplates are similar (Fig. 5) but that the inner bar plate has anadditional slot that